Building a Peer-to-Peer Network – Instructor Version (Tugas)

Indra Purnama
11108021
3KA15

Jaringan Komputer




Objective

  • Create a simple peer-to-peer network between two PCs
  • Identify the proper cable to connect the two PCs
  • Configure workstation IP address information
  • Test connectivity using the ping command.

Background / Preparation
This lab focuses on the ability to connect two PCs to create a simple peer-to-peer Ethernet LAN between
two workstations. The workstations will be directly connected to each other without using a hub or switch. In addition to the Layer 1 physical and Layer 2 data link connections, the computers must also be configured with the correct IP network settings, which is Layer 3, so that they can communicate. A basic Category 5/5e UTP crossover cable is all that is needed. A crossover cable is the same type that would be used as backbone or vertical cabling to connect switches together. Connecting the PCs in this manner can be very useful for transferring files at high speed and for troubleshooting interconnecting devices between PCs. If the two PCs can be connected with a single cable and are able to communicate, then any networking problems are not with the PCs themselves. Start this lab with the equipment turned off and with cabling disconnected. Work in teams of two with one person per PC. The following resources will be required:
  • Two workstations with an Ethernet 10/100 NIC installed
  • Several Ethernet cables, which are both straight-through and crossover, to choose from for connecting the two workstations
Step 1 Identify the proper Ethernet cable and connect the two PCs
  1. The connection between the two PCs will be accomplished using a Category 5 or 5e crossover cable. Locate a cable that is long enough to reach from one PC to the other, and attach one end to the NIC in each of the PCs. Be sure to examine the cable ends carefully and select only a crossover cable.
  2. What kind of cable is required to connect from NIC to NIC? Crossover
  3. What is the category rating of the cable? Category 5 or 5e
  4. What is the AWG wire size designation of the cable? 24 AW




Step 2 Verify the physical connection
  1. Plug in and turn on the computers. To verify the computer connections, insure that the link lights on both NICs are lit. Are both link lights lit? They should be otherwise troubleshoot.
Step 3 Access the IP settings window
Note: Be sure to write down the existing IP settings, so that they can be restored at the end of the lab. These include IP address, subnet mask, default gateway, and DNS servers. If the workstation is a DHCP client, it is not necessary to record this information.
Windows 95 / 98 / Me/ users should do the following:
  • Click on Start > Settings > Control Panel and then click the Network icon.
  • Select the TCP/IP protocol icon that is associated with the NI
    C in this PC and click on Properties.
  • Click on the IP Address tab and the Gateway tab.
Windows NT / 2000 users should do the following:
  • Click on Start > Settings > Control Panel and then open t
    he Network and Dial-up Connections folder.
  • Click ad open the Local Area Connection icon.
  • Select the TCP/IP protocol icon that is associated with the NIC in this PC.
  • Click on Properties and click on Use the following IP address.
Windows XP users should do the following:
  • Click on Start > Settings > Control Panel and then click the Network Connection icon.
  • Select the Local Area Network Connection and click on Change settings of this connection.
  • Select the TCP/IP protocol icon that is associated with the NIC in this PC.
  • Click on Properties and click on Use the following IP address.
See the example below:


Step 4 Configure TCP/IP settings for the two PCs
  1. Set the IP address information for each PC according to th e i
    nformation in the table.
  2. Note that the default gateway IP address is not require d, since these computers are directly connected. The default gateway is only required on local area networks that are connected to a router.

Computer IP Address Subnet mask Def ault Gateway
PC – A 192.168.1.1 255.255.255.0 Not Required
PC – B 192.168.1.2 255.255.255.0 Not Req uired




Step 5 Access the Command or MS-DOS prompt
Use the Start menu to open the Command Prompt (MS-DOS-like) window:
Windows 95 / 98 / Me users should do the following:
Start > Programs > MS-DOS Prompt
Windows NT / 2000 users should do the following:
Start > Programs > Accessories > Command Prompt
Windows XP users should do the following:
Start > Programs > Accessories > Command Prompt

Step 6 Verify that the PCs can communicate
  • Test connectivity from one PC to the other by pinging the IP address of the opposite computer. Use the following command at the command promp
    t.
C:>ping 192.168.1.1 (or 192.168.1.2)
  • Look for results similar to those shown below. If not, check th e PC connections and TCP/IP settings for both PCs. What was the ping result?
Results could possibly be: Sent=4 Received=3 Lost=1 (this is due to AR P)
Any other results probably indicate an error


Step 7 Confirm the TCP/IP network settings
Windows 95 / 98 / Me users should do the following:
  1. Type the winipcfg command from the MS-DOS Prompt. R ecord the results:
Answers will vary depending on if Computer A or B is used.
Examples for Computer A
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Default Gateway:

Windows NT / 2000 / XP users should do the following:
  1. Type the ipconfig command from the Command Prompt. Record the results:
Answers will vary depending on if Computer A or B is used.
Examples for Computer B
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Default Gateway:



Step 8 Restore the PCs to their original IP settings, disconnect the equipment, and store the cables

0 komentar:

Posting Komentar

 
Designed by: Indra Purnama | Bloggerized by Dhampire